Networking ConnectX-7 Firmware Release Notes

Bug Fixes in this Firmware Version

5Internal ref.

Issue

5343627 / 5105066 / 5343844 / 5343877

Description: Resolved an issue where the link failed to come up with a specific LPO (linear pluggable optics) module. Dedicated SI parameters were added for this module.

Keywords: SI parameters, LPO module

Detected in version:

28.50.1002

Fixed in release:

28.51.1002

5350445

Description: Resolved an issue where an active congestion control flow context might be outdated unexpectedly when a large number of congestion control flows are active.

Keywords: PCC

Detected in version:

28.50.1002

Fixed in release:

28.51.1002

5298967

Description: Resolved a performance degradation related to LibOS on ConnectX-7 200G adapters where running ib_write_bw on both ports at the same time reduced bandwidth.

Keywords: ib_write_bw, bandwidth, performance, dual port, LibOS

Detected in version:

28.50.1002

Fixed in release:

28.51.1002

5343689 / 5300572

Description: Resolved an issue where, under rare timing conditions, a QP scheduled for transmission could lose synchronization with the QoS scheduling mechanism. A built-in recovery flow detects this condition and re-activates the affected QP. The recovery flow is now enabled by default, and the issue that caused it to skip VFs associated with non-zero Physical Functions has been resolved.

Keywords: QP, QoS, VF, Multi-PF, BlueField, vRDMA, RoCE, transmission

Detected in version:

28.47.1026

Fixed in release:

28.51.1002

5329814 / 5344856 / NVbug 6887282

Description: Resolved an issue where NSM Type 3 Get Inventory Information manufacturing-date queries (command 0x0C, property 0x08) failed.

Keywords: NSM, VPD, serial number, manufacturing date, Get Inventory Information, ISO week

Detected in version:

28.50.1002

Fixed in release:

28.51.1002

5323929 / NVBug 6536162

Description: Resolved a PLDM firmware update failure caused by an insufficient message retry timeout. The timeout has been increased from 1 to 1.5 seconds.

Keywords: PLDM, firmware update, retry timeout

Detected in version:

28.48.1000

Fixed in Release:

28.51.1002

4601097 / NVBug 5166755

Description: Resolved an issue in ERoT metadata where flash addresses used during firmware upgrade were defined for a 32Mb flash layout. On B200 platforms, which use a 64Mb flash with a different memory layout, this caused incorrect address mapping when copying data between flashes. The addresses have been corrected to align with the 64Mb flash layout.

Keywords: ERoT, flash layout, B200, firmware upgrade, address mapping

Detected in version:

28.50.1002

Fixed in Release:

28.51.1002

5299142

Description: Resolved a firmware fatal assert (ext_synd 0x75) caused by CRspace writes targeting latency counter blocks that were not backed by hardware logic. The latency block whitelist has been updated to prevent such writes from being processed by the firmware.

Keywords: ext_synd 0x75, CRspace, latency block whitelist, fatal assert

Detected in version:

28.50.1002

Fixed in Release:

28.51.1002

5257510

Description: Resolved an I2C driver issue where read transactions to MCTP addresses caused non-compliant SCL clock stretching. The timeout is now aligned to the SMBus specification (25 ms).

Keywords: I2C, MCTP, SCL clock stretching, SMBus

Detected in version:

28.50.1002

Fixed in Release:

28.51.1002

5235696

Description: Resolved incorrect handling of MACsec confidentiality-offset values during conversion between the software interface and the hardware SADB, which could result in improper packet encryption.

Keywords: MACsec, confidentiality-offset, SADB, packet encryption

Detected in version:

28.50.1002

Fixed in Release:

28.51.1002

5157189 / 4866555

Description: Resolved an issue where, when massive flows occurred in parallel with PCC, INIT2RTR could report a false alarm with syndrome 0x7 "dead IRISC."

Keywords: IRISC, dead IRISC, PCC, INIT2RTR, syndrome 0x7

Detected in version:

28.47.1026

Fixed in Release:

28.51.1002

5130021

Description: Resolved a ZTR RTT CC issue where the CNP_VLD_RTT parameter was ignored on the first congestion event, causing the algorithm to misinterpret a large RTT value as congestion and reduce bandwidth.

Keywords: ZTR RTT CC, CNP_VLD_RTT, congestion, RDMA BW

Detected in version: 

28.49.1014

Fixed in release: Host FW 51.1000

5099299 / 5122462

Description: Resolved several PLDM RDE (Type 6) issues, including: Port.Reset action failure on ports that were not link-up; incomplete multipart request payload transfers; missing validation of declared request payload lengths against the message content.

Keywords: PLDM RDE, Type 6, Port.Reset, multipart transfer

Detected in version:

28.49.1014

Fixed in Release:

28.51.1002

5093878 / 5138237

Description: Resolved a credit leak and resulting TX timeouts that occurred when a DPA application used cross-VHCA, cross-host doorbell messaging via DPA Outbox.

Keywords: DPA Outbox, credit leak, TX timeout, cross-VHCA, doorbell

Detected in version:

28.46.3048

Fixed in Release:

28.51.1002

5081175

Description: Resolved a ZTR RTT CC issue in topology-aware mode where fabric round-trip times exceeding 200 µs caused false congestion signals and sustained below-line-rate throughput.

Keywords: ZTR RTT CC, topology-aware, fabric RTT, congestion

Detected in version:

28.50.1002

Fixed in Release:

28.51.1002

5019624

Description: Resolved an issue where a PCIe SBR did not reset the MCTP discovery state, causing the device to miss EndpointDiscovery requests.

Keywords: PCIe SBR, MCTP, EndpointDiscovery, reset

Detected in version:

28.50.1002

Fixed in Release:

28.51.1002

4988444

Description: Resolved a false-positive "IRISC stuck" detection after cold reboot on Windows.

Keywords: IRISC stuck, Windows, cold reboot, false positive

Detected in version:

28.49.1014

Fixed in Release:

28.51.1002

Last updated: