|
Internal Ref. |
Issue |
|---|---|
|
4241238 |
Description: Fixed TX timeout issue related to the esw_scheduling QoS feature. |
|
Keywords: esw_scheduling QoS
|
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4352025 |
Description: Fixed an out-of-space issue related to writing Type-Length-Value (TLV) entries to reclaim space by removing outdated or irrelevant configuration entries. |
|
Keywords: TLV
|
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4318537 |
Description: Fixed an issue where the AI and HAI parameters of the ZTR_RTTCC algorithm, when configured by users, were automatically overwritten upon link speed changes. With this fix, if AI/HAI values were tuned for link speeds other than 100Gb/s, users should now divide those values by (link_speed / 100) to maintain consistent congestion control algorithm behavior. |
|
Keywords: Congestion control, ZTR_RTTCC
|
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4368450 |
Description: Fixed an issue where |
|
Keywords: PCC |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4360664 |
Description: Fixed an issue in DOCA Telemetry recovery following a non-graceful abort or driver restart. The problem was related to configuring certain counters during the post-abort flow. |
|
Keywords: DOCA Telemetry recovery |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4311009 |
Description: Fixed an issue with doorbell recovery that occurred when DCS was active in the system that resulted in the FLR/DESTROY_QP command getting stuck. |
|
Keywords: DCS, doorbell recovery |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4161925 |
Description: Fixed an issue where the CDB command timeout needed to be increased due to background traffic. |
|
Keywords: CDB |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4295491 |
Description: Fixed a rare race condition that could incorrectly detect a lack of communication between the ASICs, resulting in module failure and incorrect reporting as unplugged. |
|
Keywords: Race condition |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4342585 |
Description: Fixed an issue where TLV with OEM priority was incorrectly processed if blocked by MLNX TLV (over_en=0). |
|
Keywords: TLV |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4209790 |
Description: Enhanced execution time and reduced memory consumption for ETH transport resources (TIR, Transport Domain). |
|
Keywords: ETH transport resources |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4257863 |
Description: Fixed an issue that could cause the DESTROY_MKEY command to take an excessively long time to execute, with the host driver displaying a "No done completion" message for this command. |
|
Keywords: MKey |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4208995 |
Description: Fixed a timing race between Rx tuning and CDR locking following exit from electrical idle. |
|
Keywords: Timing race, Rx, CDR |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4239221 |
Description: Fixed an issue where performing a software reset could cause the device to become inaccessible, requiring a reboot to restore visibility. |
|
Keywords: sw reset |
|
|
Discovered in Version: 28.43.1014 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4274327 |
Description: Fixed an issue in the VQoS algorithm related to learning when an element is active and when it begins sending traffic. |
|
Keywords: VQoS algorithm |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4222773 |
Description: Reduced the bandwidth fluctuation induced by VQoS rate limiting in systems with bellow 350 QPs. Note: In this release, the relevant change is enabled by default, while in future versions it will be disabled by default and an additional NV configuration will be required to enable it. |
|
Keywords: VQoS |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4274669 |
Description: Fixed a race condition that could prevent the application from transmitting when VQoS is enabled. |
|
Keywords: VQoS |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4319008 |
Description: Fixed an issue that caused bandwidth to drop when unbinding multiple VFs with VQoS enabled. |
|
Keywords: VQoS |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
|
|
4199274 |
Description: Fixed an issue where RTT packets with any destination MAC address were incorrectly treated as having a valid destination MAC. The new firmware now discards RTT packets if their destination MAC does not match the port's MAC. |
|
Keywords: RTT, destination MAC |
|
|
Discovered in Version: 28.44.1036 |
|
|
Fixed in Release: 28.45.1020 |
Last updated: