Statistics and Alarms

stats alarm clear

	stats alarm <alarm-id> clear Clears alarm state.
Syntax Description	alarm-id	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating system disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
Default	N/A
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats alarm cpu_util_indiv clear`
Related Commands	show stats alarm
Notes

stats alarm enable

	stats alarm <alarm-id> enable no stats alarm <alarm-id> enable Enables the alarm. The no form of the command disables the alarm. Notifications will not be received.
Syntax Description	alarm-id	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating system disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
Default	The default is different per alarm ID
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats alarm cpu_util_indiv enable`
Related Commands	show stats alarm
Notes

stats alarm event-repeat

	stats alarm <alarm-id> event-repeat {single \| while-not-cleared} no stats alarm <alarm-id> event-repeat Configures repetition of events from this alarm.
Syntax Description	alarm-id	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating system disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
	single	Does not repeat events: only sends one event whenever the alarm changes state
	while-not-cleared	Repeats error events until the alarm clears
Default	Single
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats alarm cpu_util_indiv event-repeat single`
Related Commands	show stats alarm
Notes

stats alarm {rising | falling}

	stats alarm <alarm-id> {rising \| falling} {clear-threshold \| error-threshold} <threshold-value> Configure alarms thresholds.
Syntax Description	alarm-id	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating system disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
	rising	Configures alarm for when the statistic rises too high
	falling	Configures alarm for when the statistic falls too low
	error-threshold	Sets threshold to trigger falling or rising alarm
	clear-threshold	Sets threshold to clear falling or rising alarm
	threshold-value	Threshold value, different per alarm
Default	Default is different per alarm ID
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats alarm cpu_util_indiv falling clear-threshold 10`
Related Commands	show stats alarm
Notes	Not all alarms support all four thresholds.

stats alarm rate-limit

	stats alarm <alarm-id> rate-limit {count <count-type> <count> \| reset \| window <window-type> <duration>} Configures alarms rate limit.
Syntax Description	alarm-id	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating system disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
	count-type	Long medium, or short count (number of alarms)
	reset	Set the count and window durations to default values for this alarm
	window-type	Long medium, or short count, in seconds
Default	Short window: 5 alarms in 1 hour Medium window: 20 alarms in 1 day Long window: 50 alarms in 7 days
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats alarm paging rate-limit window long 2000`
Related Commands	show stats alarm
Notes

stats chd clear

	stats chd <chd-id> clear Clears CHD counters.
Syntax Description	chd-id	CHD supported by the system, for example: cpu_util – CPU utilization: percentage of time spent cpu_util_ave – CPU utilization average: percentage of time spent cpu_util_day – CPU utilization average: percentage of time spent disk_device_io_hour – storage device I/O read/write statistics for the last hour: bytes disk_io – operating system aggregate disk I/O average: KB/sec eth_day eth_hour fs_mnt_day – filesystem system usage average: bytes fs_mnt_month – filesystem system usage average: bytes fs_mnt_week – –ilesystem system usage average: bytes ib_day ib_hour intf_day – network interface statistics aggregation: bytes intf_hour – network interface statistics (same as “interface” sample) intf_util – aggregate network utilization across all interfaces memory_day – average physical memory usage: bytes memory_pct – average physical memory usage paging – paging activity: page faults paging_day – paging activity: page faults
Default	N/A
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats chd memory_day clear`
Related Commands	show stats chd
Notes

stats chd enable

	stats chd <chd-id> enable no stats chd <chd-id> enable Enables the CHD. The no form of the command disables the CHD.
Syntax Description	chd-id	CHD supported by the system, for example: cpu_util – CPU utilization: percentage of time spent cpu_util_ave – CPU utilization average: percentage of time spent cpu_util_day – CPU utilization average: percentage of time spent disk_device_io_hour – storage device I/O read/write statistics for the last hour: bytes disk_io – operating system aggregate disk I/O average: KB/sec eth_day eth_hour fs_mnt_day – filesystem system usage average: bytes fs_mnt_month – filesystem system usage average: bytes fs_mnt_week – –ilesystem system usage average: bytes ib_day ib_hour intf_day – network interface statistics aggregation: bytes intf_hour – network interface statistics (same as “interface” sample) intf_util – aggregate network utilization across all interfaces memory_day – average physical memory usage: bytes memory_pct – average physical memory usage paging – paging activity: page faults paging_day – paging activity: page faults
Default	Enabled
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats chd memory_day enable`
Related Commands	show stats chd
Notes

stats chd compute time

	stats chd <chd-id> compute time {interval \| range} <time> Sets parameters for when this CHD is computed.
Syntax Description	chd-id	CHD supported by the system, for example: cpu_util – CPU utilization: percentage of time spent cpu_util_ave – CPU utilization average: percentage of time spent cpu_util_day – CPU utilization average: percentage of time spent disk_device_io_hour – storage device I/O read/write statistics for the last hour: bytes disk_io – operating system aggregate disk I/O average: KB/sec eth_day eth_hour fs_mnt_day – filesystem system usage average: bytes fs_mnt_month – filesystem system usage average: bytes fs_mnt_week – –ilesystem system usage average: bytes ib_day ib_hour intf_day – network interface statistics aggregation: bytes intf_hour – network interface statistics (same as “interface” sample) intf_util – aggregate network utilization across all interfaces memory_day – average physical memory usage: bytes memory_pct – average physical memory usage paging – paging activity: page faults paging_day – paging activity: page faults
	interval	Specifies calculation interval (how often to do a new calculation) in number of seconds
	range	Specifies calculation range, in number of seconds
	time	Number of seconds
Default	Different per CHD
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats chd memory_day compute time interval 120`
Related Commands	show stats chd
Notes

stats sample clear

	stats sample <sample-id> clear Clears sample history.
Syntax Description	sample-id	Possible sample IDs are: congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec eth fan – fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes ib interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature
Default	N/A
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats sample temperature clear`
Related Commands	show stats sample
Notes

stats sample enable

	stats sample <sample-id> enable no states sample <sample-id> enable Enables the sample. The no form of the command disables the sample.
Syntax Description	sample-id	Possible sample IDs are: congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec eth fan – fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes ib interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature
Default	Enabled
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats sample temperature enable`
Related Commands	show stats sample
Notes

stats sample interval

	stats sample <sample-id> interval <time> Sets the amount of time between samples for the specified group of sample data.
Syntax Description	sample-id	Possible sample IDs are: congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec eth fan – fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes ib interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature
	time	Number of seconds
Default	Different per sample
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats sample temperature interval 1`
Related Commands	show stats sample
Notes

stats clear-all

	stats clear all Clears data for all samples, CHDs, and status for all alarms.
Syntax Description	N/A
Default	N/A
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats clear-all`
Related Commands	show stats sample
Notes

stats export

	stats export <format> <report-name> [{after \| before} <yyyy/mm/dd> <hh:mm:ss>] [filename <filename>] Exports statistics to a file.
Syntax Description	format	Currently the only supported value for <format> is "csv" (comma-separated value)
	report-name	Determines dataset to be exported. Possible report names are: memory – memory utilization paging – paging I/O cpu_util – CPU utilization
	after \| before	Only includes stats collected after or before a specific time
	yyyy/mm/dd	Date must be between 1970/01/01 and 2038/01/19
	hh:mm:ss	Time must be between 00:00:00 and 03:14:07 UTC and is treated as local time
	filename	Specifies filename to give new report. If a filename is specified, the stats will be exported to a file of that name; otherwise a name will be chosen automatically and will contain the name of the report and the time and date of the export. Any automatically-chosen name will be given a .csv extension.
Default	N/A
Configuration Mode	config
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # stats export csv memory filename mellanoxexample before 2000/08/14 15:59:50 after 2000/08/14 15:01:50 Generated report file: mellanoxexample.csv`
Related Commands	show files stats
Notes

show stats alarm

	show stats alarm [<alarm-id> [rate-limit]] Displays status of all alarms or the specified alarm.
Syntax Description	alarm-id	cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating system disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
	rate-limit	Displays rate limit parameters
Default	N/A
Configuration Mode	Any configuration mode
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # show stats alarm Alarm cpu_util_indiv (Average CPU utilization too high): ok Alarm disk_io (Operating System Disk I/O per second too high): (disabled) Alarm fs_mnt (Free filesystem space too low): ok Alarm intf_util (Network utilization too high): (disabled) Alarm memory_pct_used (Too much memory in use): (disabled) Alarm paging (Paging activity too high): ok Alarm temperature (Temperature is too high): ok`
Related Commands	stats alarm
Notes

show stats chd

	show stats chd [<chd-id>] Displays configuration of all statistics CHDs.
Syntax Description	chd-id	cpu_util – CPU utilization: percentage of time spent cpu_util_ave – CPU utilization average: percentage of time spent cpu_util_day – CPU utilization average: percentage of time spent disk_device_io_hour – storage device I/O read/write statistics for the last hour: bytes disk_io – operating system aggregate disk I/O average: KB/sec eth_day eth_hour fs_mnt_day – filesystem system usage average: bytes fs_mnt_month – filesystem system usage average: bytes fs_mnt_week – –ilesystem system usage average: bytes ib_day ib_hour intf_day – network interface statistics aggregation: bytes intf_hour – network interface statistics (same as “interface” sample) intf_util – aggregate network utilization across all interfaces memory_day – average physical memory usage: bytes memory_pct – average physical memory usage paging – paging activity: page faults paging_day – paging activity: page faults
Default	N/A
Configuration Mode	Any configuration mode
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # show stats chd disk_device_io_hour CHD "disk_device_io_hour" (Storage device I/O read/write statistics for the last hour: bytes): Enabled: yes Source dataset: sample "disk_device_io" Computation basis: data points Interval: 1 data point(s) Range: 1 data point(s)`
Related Commands	stats chd
Notes

show stats cpu

	show stats cpu Displays some basic stats about CPU utilization: the current level the peak over the past hour the average over the past hour
Syntax Description	N/A
Default	N/A
Configuration Mode	Any configuration mode
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # show stats cpu CPU 0 Utilization: 6% Peak Utilization Last Hour: 16% at 2012/02/28 08:47:32 Avg. Utilization Last Hour: 8%`
Related Commands
Notes

show stats sample

	show stats sample [<sample-id>] Displays sampling interval for all samples, or the specified one.
Syntax Description	sample-id	congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec eth fan – fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes ib interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature
Default	N/A
Configuration Mode	Any configuration mode
History	1.5
Example	`ufmapl [ mgmt-sa ] (config) # show stats sample fan Sample "fan" (Fan speed): Enabled: yes Sampling interval: 1 minute 11 seconds`
Related Commands	stats sample
Notes

Last updated: August 22, 2020